[ Pobierz całość w formacie PDF ]

129 65 insight.ifna.org
143 N/A fidogate.ifna.org
152 200 castle.ifna.org
161 N/A fidogate.ifna.org
369 17 megasys.ifna.org
NOTE: The UUCP equivalent node name is the first part of the node name. In other words, the UUCP node milehi is listed as milehi.ifna.org
but can be mailed directly over the UUCP network.
Another way to mail to FIDONET, specifically for Internet people, is in this format:
ihnp4!necntc!ncoast!ohiont!!!user_name@husc6.harvard.edu
And for those UUCP mailing people out there, just use the path described and ignore the @husc5.harvard.edu portion. There is a FIDONET
NODELIST available on most any FIDONET bulletin board, but it is quite large.
ONTYME
Previously known as Tymnet, OnTyme is the McDonnell Douglas revision. After they bought out Tymnet, they renamed the company and
opened an experimental Internet gateway at ONTYME.TYMNET.COM but this is supposedly only good for certain corporate addresses within
McDonnell Douglas and Tymnet, not their customers. The userid format is xx.yyy or xx.y/yy where xx is a net name and yyy (or y/yy) is a true
username. If you cannot directly nail this, try:
xx.yyy%ONTYME.TYM
130.Sodium Chlorate by the Jolly Roger
Sodium Chlorate is a strong oxidizer used in the manufacture of explosives. It can be used in place of Potassium Chlorate.
Material Required:
"
2 carbon or lead rods (1 in. diameter by 5 in. long)
"
Salt, or ocean water
"
Sulfuric acid, diluted
"
Motor Vehicle
"
Water
"
2 wires, 16 gauge (3/64 in. diameter approx.), 6 ft. long, ins ulated.
"
Gasoline
"
1 gallon glass jar, wide mouth (5 in. diameter by 6 in. high approx.)
"
Sticks
"
String
"
Teaspoon
"
Trays
"
Cup
"
Heavy cloth
"
Knife
"
Large flat pan or tray
Sources of Carbon or Lead rods:
"
Dry Cell Batteries (2-« in. diameter by 7" long) or plumbing supply store.
Sources of Salt Water:
"
Grocery store or ocean
Sources of Sulfuric Acid:
"
Motor Vehicle Batteries.
Procedure:
1.Mix « cup of salt into the one gallon glass jar with 3 liters (3 quarts) of water.
2.Add 2 teaspoons of battery acid to the solution and stir vigorously for 5 minutes.
3.Strip about 4 inches of insulation from both ends of the two wires.
4.With knife and sticks, shape 2 strips of wood 1 by 1/8 by 1-«. Tie the wood strips to the lead or carbon rods so that they are 1-« inches
apart.
5.Connect the rods to the battery in a motor vehicle with the insulated wire.
6.Submerge 4-« inches of the rods in the salt water solution.
7.With gear in neutral position, start the vehicle engine. Depress the accelerator approx. 1/5 of its full travel.
8.Run the engine with the accelerator in this position for 2 hours, then shut it down for 2 hours.
9.Repeat this cycle for a total of 64 hours while maintaining the level of the acid-salt water solution in the glass jar.
CAUTION: This arrangement employs voltages which can be quite dangerous!
Do not touch bare wire leads while engine is running!!
10.Shut off the engine. Remove the rods from the glass jar and disconnect wire leads from the battery.
11.Filter the solution through the heavy cloth into a flat pan or tray, leaving the sediment at the bottom of the glass jar.
12.Allow the water in the filtered solution to evaporate at room temperature (approx. 16 hours). The residue is approximately 60% or more
sodium chlorate which is pure enough to be used as an explosive ingredient.
131.Mercury Fulminate by the Jolly Roger
Mercury Fulminate is used as a primary explosive in the fabrication of detonators. It is to be used with a booster explosive such as picric acid
or RDX (which are elsewhere in this Cookbook).
Material Required:
"
Nitric Acid, 90% conc. (1.48 sp. gr)
"
Mercury
"
Ethyl (grain) alcohol (90%)
"
Filtering material [Paper Towels]
"
Teaspoon measure (¬, «, and 1 tsp. capacity)-aluminum, stainless steel or wax coated
"
Heat Source
"
Clean wooden stick
"
Clean water
"
Glass containers
"
Tape
"
Syringe
Source of Nitric Acid:
"
Elsewhere in this Cookbook
"
Industrial metal processors
Source of Mercury:
"
Thermometers
"
Mercury switches
"
Old radio tubes
Procedure:
1.Dilute 5 teaspoons of nitric acid with 2-« teaspoons of clean water in a glass container by adding the acid to the water.
2.Dissolve 1/8 teaspoon of mercury in the diluted nitric acid. This will yield dark red fumes. NOTE: It may be necessary to add water, on drop at
a time, to the mercury-acid solution in order to start a reaction.
"
CAUTION: Acid will burn skin and destroy clothing. If any is spilled, wash it away with a large quantity of water. Do NOT inhale
fumes!
3.Warm 10 teaspoons of the alcohol in a container until the alcohol feels warm to the inside of the wrist.
4.Pour the metal-acid solution into the warm alcohol. Reaction should start in less than 5 minutes. Dense white fumes will be given off during
the reaction. As time lapses, the fumes will become less dense. Allow 10 to 15 minutes to complete reaction. Fulminate will settle to the
bottom.
"
CAUTION: This reaction generates large quantities of toxic, flammable fumes. The process MUST be conducted outdoors or in a
well -ventilated area, away from sparks or open flames. DO NOT inhale fumes!
5.Filter the solution through a paper towel into a container. Crystals may stick to the side of the container. If so, tilt and squirt water down the
sides of the container until all of the material collects on the filter paper.
6.Wash the crystals with 6 teaspoons of ethyl alcohol. [ Pobierz całość w formacie PDF ]